Production of carbon soot with a high content of C60 and C70 fullerenes by electric arc

The effect of the parameters of the electric arc (helium pressure, current and voltage, clearance between electrodes) and of the peculiarities of the setup design (arrangement of electrodes, distance between the arc and the cooling surface, temperature of the soot condensation surface) on the yield of fullerenes has been studied. Conditions for producing soot with a C₆₀ and C₇₀ content up to 43% (toluene extract) have been found.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 805–809, May, 1994.The authors are grateful to N. G. Spitsyna and A. V. Dubovitskii for the determination of the content of C₆₀ and C₇₀ fullerenes in the extract.The work was financially supported by the Russian Foundation for Basic Research (Project 93-03-18705).     

Interaction of carbon dioxide with ditoluenetitanium

The interaction of ditoluenetitanium with CO{in2} has been studied. Based on hydrolysis, thermolysis, and IR spectral data, the conclusion is drawn that a low-valent titanium oxalate is formed.This study was financially supported by the Russian Foundation for Basic Research (Project No. 93-03-5538).Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 12, pp. 2241–2242, December, 1994.     

(NH4)2MoS4在活性炭上浸渍过程的研究:Ⅱ.干燥机理及模型

（ＮＨ＿４）＿２ＭｏＳ＿４在活性炭上浸渍过程的研究Ⅱ．干燥机理及模型秦慧芳，张成芳，陆岗，俞丰，朱子彬（华东理工大学无机化工研究所，上海２００２３７）２３７）关键词硫代钼酸铵，活性炭，干燥，钼分布，干燥模型负载型催化剂的活性组分在载体上的分布，受浸渍...     

Preparation of well-aligned carbon nanotubes by pyrolysis of phenolic resin in anodic alumina pores

Well-aligned carbon nanotubes (CNTs) of high quality were synthesized by pyrolysis of phenolic resin at 800 °C in anodic alumina oxide (AAO) pores under argon protection. The innocuous source materials and safe operational conditions permit this method to synthesize well-aligned CNTs in large-scale and low cost. The formation mechanism of the synthesized CNTs is also proposed in this work by a series of visual sketches and is proved with obvious evidence. Firstly, phenolic resin nanotubes form in the template pores through the evaporation of solvent. Heat treatment then transfers these tubes into CNTs.     

Effect of nanotube functionalization on the properties of single‐walled carbon nanotube/polyurethane composites

A commercially available aliphatic thermoplastic polyurethane formulated with a methylene bis(cyclohexyl) diisocyanate hard segment and a poly(tetramethylene oxide) soft segment and chain‐extended with 1,4‐butanediol was dissolved in dimethylformamide and mixed with dispersed single‐walled carbon nanotubes. The properties of composites made with unfunctionalized nanotubes were compared with the properties of composites made with nanotubes functionalized to contain hydroxyl groups. Functionalization almost eliminated the conductivity of the tubes according to the conductivity of the composites above the percolation threshold. In most cases, functionalized and unfunctionalized tubes yielded composites with statistically identical mechanical properties. However, composites made with functionalized tubes did have a slightly higher modulus in the rubbery plateau region at higher nanotube fractions. Small‐angle X‐ray scattering patterns indicated that the dispersion reached a plateau in the unfunctionalized composites that was consistent with the plateau in the rubbery plateau region. The room‐temperature modulus and tensile strength increase was proportionally higher than almost all increases seen previously in thermoplastic polyurethanes; however, the increase was still an order of magnitude below what has been reported for the best nanotube–polymer systems. Nanotube addition increased the hard‐segment glass transition temperature slightly, whereas the soft‐segment glass transition was so diffuse that no conclusions could be drawn. Unfunctionalized tubes suppressed the crystallization of the hard segment; whereas functionalized tubes had no effect. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 490–501, 2007     

Competitive influence of atactic polystyrene and supercritical carbon dioxide on the conformation of syndiotactic polystyrene

The crystallization behavior of miscible syndiotactic polystyrene (sPS) and atactic polystyrene (aPS) blends with different sPS/aPS weight ratios was investigated in supercritical CO₂ by using Fourier‐transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Supercritical CO₂ and aPS exhibited different effects on the conformational change of sPS and competed with each other. Increasing the content of amorphous aPS in the blends made its effect on the conformational change of sPS gradually surpass that of supercritical CO₂. Supercritical CO₂ favored the formation of the helical conformation of sPS in lower temperature range and the all trans planar conformation in higher temperature range, instead of forming the latter one only in higher temperature range in ambient atmosphere. However, increasing aPS content in the blends pushed the range for forming the helical conformation to lower temperature and made the all trans planar conformation dominant in aPS/sPS 25/75 blend after treating in supercritical CO₂ above 60 °C. The all trans planar zigzag conformation was more favorable than the helical conformation after mixing aPS in sPS in supercritical CO₂. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1755–1764, 2007     

Photocatalytic Synthesis of Oxygenates from Gaseous CO2 and CH4 over Semiconductor

Photoinduced synthesis of CO2 and CH4 was investigated using a batch reaction system on several photoactive materials supported on silicon dioxide. Single semiconductor showed higher selectivity to C1 compounds. The production of C2-C3 oxygenates took place preferentially on composite semiconductor photocatalysts. In particular, it was found that acetone was the primary product over Cu/CdS-TiO2/SiO2.     

大黄酸修饰电极对细胞色素C的催化还原

研究了大黄酸修饰电极的性质及对细胞色素C的催化还原，并研究了其电极应用机理。     

Gradient‐enhanced one‐dimensional pulse schemes for quaternary and methylene carbon detection

Gradient‐enhanced pulse schemes are presented for the detection of quaternary and methylene carbons. The new pulse schemes permit the detection of quaternary and methylene (—CH₂) carbons or CH₂ carbons alone from a single experiment. Efficient suppression of CH and CH₃ carbons in all the pulse schemes is achieved by creating their antiphase magnetization and then dephasing using gradients. In the pulse schemes for detection of only CH₂ carbons, the quaternary carbons are also suppressed either by dephasing using gradients or by rendering them unobservable by retaining in longitudinal order. The experimental results of the gradient pulse schemes are demonstrated on cholesteryl acetate and cyclosporin A. These one‐dimensional techniques, because of their simplicity and the ease of performing the experiments, can be important for routine chemical applications. Copyright © 2003 John Wiley & Sons, Ltd.     

Alternating copolymerization of carbon dioxide and epoxide by manganese porphyrin: The first example of polycarbonate synthesis from 1-atm carbon dioxide

The first successful example of the formation of polycarbonate from 1-atm carbon dioxide and epoxide was demonstrated by the alternating copolymerization of carbon dioxide and epoxide with manganese porphyrin as a catalyst. The copolymerization of carbon dioxide and cyclohexene oxide with (porphinato)manganese acetate proceeded under the 1-atm pressure of carbon dioxide to give a copolymer with an alternating sequence. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 3549–3555, 2003